亚洲国产综合精品一区,少妇高潮a片特黄久久精品网,欧洲性xxxx免费视频在线观看,国产精品尹人在线观看,成人免费午夜福利片在线观看

TFLS系列 音叉式料位開關*適用于粉體物料和顆粒物料，特別是低密度物料的料位監控。它采用壓電水晶帶動音叉以其自然頻率振動，當音叉接觸到物料會阻尼改變振動，開關會動作，而當物料離開音叉后，開關會還原到原有的位置。TFLS可選開關狀態的故障安全模式。它不會受到系統中物料輸送，馬達等振動的影響，并且可以任意方向安裝，可定制加長的音叉用于槽罐的頂部安裝。TFLS料位開關無需校準，容易使用，它不帶任何機械移動部件，不需要日常維護。它不受物料的介電常數的影響，能用于當介電常數低的物料不適宜用電容式物料開關的場合，特別是用于混合物料的場合，和物料干濕度經常變化的場合。音叉料位開關也特別適合于物料密度很低，無法采用旋葉式料位開關的場合，它也能用于監控液體中顆粒物料的液體固體分界面。

LTC系列 傾斜開關料位控制器帶有邏輯選擇開關，還可以調整延遲時間。 邏輯選擇開關的作用是決定繼電器什么時候動作或解除動作。第一種方式是探頭垂直時繼電器動作，當探頭成角度時繼電器解除動作。第二種方式的動作正好相反。繼電器延時動作的功能能用于垂直或角度的狀態，以避免誤動作。繼電器在延時完后會解除動作，在失電的情況下，繼電器也會解除動作。

產品介紹：SITRANS LVL100是一款一體式振動物位開關，用于諸如溢流、高、低和所需的應用，還有泵保護。對于有限空間內的使用是理想的。SITRANS LVL100是一款一體式物位開關，是為了過程技術的所有領域中的工業使用而設計的，可以同液體和漿體一起使用。其插入長度僅為40 mm (1.57“),SITRANS LVL100可以被安裝在小管道或有限空間應用中。它幾乎不受液體的化學和物理屬性的影響。LVL100亦可在包含湍流、氣泡、泡沫、積累或強外部振動的不同應用中使用。音叉是壓電通電的，以大概為1200Hz的機械共振頻率振動。當音叉被介質覆蓋的時候振動頻率就改變，這個改變是由集成的振蕩器檢測到的，然后轉換為一個開關命令。集成的電子器件估算物位信號，然后輸出一個開關信號，直接地操作連接的設備。關鍵應用：液體和漿體中的使用、物位測量、溢出和空運行保護詳情范圍40 mm (1.5”)插入空間過程溫度-40 – 150 °C (-40 – 302  °F)過程壓力-1 – 64 bar g (-14.5 – 928 psi g)特點液體經驗證的診斷物位開關技術有限空間應用的一體式40 mm (1.57”)插入長度腐蝕、振動損失或壓力驅動的輸送管線斷裂的故障監控

產品介紹：SITRANS LVL200是一款標準型振動物位開關，用于諸如溢流、高、低和所需應用的所有液體和漿體應用中的使用，還有泵保護。用于SIL-2應用中的使用。SITRANS LVL200是一款一體式物位開關，是為了過程技術的所有領域中的工業使用而設計的，可以同液體和漿體一起使用。其插入長度僅為40 mm (1.57“),SITRANS LVL100可以被安裝在小管道或有限空間應用中。LV200可以用于測量*小密度大于0.5 g/cm3 (0.018 lbs/in3)的產品。LVL200亦可在包含湍流、氣泡、泡沫、積累或強外部振動的不同應用中使用。SITRANS LVL200通過頻率估算連續地監控故障，提供音叉強腐蝕或損壞的、振動損失、或壓力驅動的管線斷裂的早期檢測。音叉是壓電通電的，以大概為1200Hz的機械共振頻率振動。當音叉被介質覆蓋的時候振動頻率就改變，這個改變是由集成的振蕩器檢測到的，然后轉換為一個開關命令。集成的電子器件估算物位信號，然后輸出一個開關信號，直接地操作連接的設備。關鍵應用：液體和漿體中的使用、物位測量、溢出和空運行保護。詳情范圍40 mm – 4 m (1.5” – 13 ft)過程溫度-50 – 250 °C (-58 – 482 °F)過程壓力 -1 – 64 bar g (-14.5 – 928 psi g)特點液體經驗證的診斷物位開關技術有限空間應用的一體式40 mm (1.57”)插入長度腐蝕、振動損失或壓力驅動的輸送管線斷裂的故障監控高物位和空運行應用的SIL 2資格衛生的過程連接件

產品介紹：Pointek ULS200是一款帶兩個開關點的超聲波非接觸開關，用于多種工業中批量固體、液體和漿體的物位檢測；對于粘性原料是理想的開關。批量固體的測量范圍**為3 m (9.8 ft)，液體和漿體的為5 m (16.4 ft)。不同于侵入式接觸設備，它在傳感器上沒有原料積累。該物位開關有一個堅固的設計，在一個耐用的設備中組合了傳感器和電子器件。它沒有移動部件，幾乎是不需要維護的。該傳感器有可用的ETFE或PVDF共聚物的，對于大多數化學物是惰性的。這意味著該設備可以在化學、石油化學、水和廢水行業。ULS200的衛生型，帶一個工業標準的法蘭選項，在應用中可易于被移除以進行清理。它因此滿足在食品、飲料、制藥行業中使用的前提。Pointek ULS200提供了優越的性能的同時亦減少了維護、停工、設備更換成本。關鍵應用：液體、漿體、流體原料、塞緊的滑道檢測、化學行業詳情范圍液體：0.25 m – 5 m (0.8 – 16 ft) 固體：0.25 m – 3 m (0.8 – 10 ft)過程溫度-40 – 60 °C (-40 – 140 °F)過程壓力高至0.5 bar g (7.25 psi g)特點用于高-高、高、低、低-低物位警報的2開關輸出或泵啟/?？刂萍蓽囟妊a償AC或DC電源電子器件支持故障安全功能螺紋和衛生裝配鉗狀過程連接件聚碳酸酯或鋁外殼，類別6/NEMA 6/IP67簡單的雙按鈕編程

OLS系列 光學液位開關價格低，堅固耐用，穩定可靠。不帶有任何可移動的部件，反應速度快。它帶有紅色和綠色的LED狀態指示燈。有三種材質供選擇：316不銹鋼，聚砜，PFA工程塑料。結構小巧，可任意方向安裝。工作原理OLS光學液位開光采用了發射紅外線的LED，光線射入棱鏡后進行兩個90°的折射回到光電晶體管，由于棱鏡周圍是氣體，光源就會返回光電晶體管，當液體處于光源和棱鏡的接觸點時，光就會折射入液體中而不會射入并觸發光電晶體管。

A unique, patented Magnetic Linkage isolates the electrical compartment from controlled product, reducing maintenance and improving sensitivity. The sealed switch compartment and sealed leads yield the utmost in reliable operation. A wide selection of diaphragms and switches is available with choices of flange or suspension mounting to fit your specific application. The dry level Ultra-Mag? Level Switch is extremely sensitive and very economical. The magnetic linkage makes this simple explosion-proof diaphragm switch the most rugged and reliable level control for a variety of products.Mounting Selection: A choice of either suspension or flange mounting is available to match your application. Flange mounting is the best choice for control of low or intermediate level in vessels containing granular product that does not "bridge", "rathole", or otherwise build up on vessel walls. Choose suspension mounting for high level in vessels and for better operation with "bridging" product. See below for more information on suspension and flange mounting kits. Note that the mounting configuration is represented by the letter "S" for suspension or "F" for flange which is the second digit in the part number.Diaphragm Selection: A wide variety of diaphragms is available to match product bulk density, flowability, abrasiveness and temperature requirements while providing maximum sensitivity. The best choice for vessels subject to pressure or vacuum is "breathable" fabric (P Series), requiring no venting. Non-porous elastomer (G Series) type diaphragms are the best choice for more abrasive product and broader temperature range applications. Venting is always required with the G series and if used in pressurized vessels, venting to the tank atmosphere is required to allow pressure equalization. A slide rule "Diaphragm Selector" is available from the factory to help you choose the diaphragm best suited to your application.Suspension Mounting is normally used for high level monitoring in vessels. For product over 20 lbs./cu. ft., the level switch (diaphragm face) should be located about 1/3 of the distance from the vessel wall to the point of entry of the product. For product less than 20 lbs./cu. ft., the unit should be located closer to the point of entry of the product, about 1/2 the distance from the vessel wall to the point of entry. Pressure required to depress the diaphragm and trip the switch is in the range of 5-15 oz in the horizontal direction (perpendicular to the diaphragm). Suspension mounting provides the easiest vertical adjustment capability, greatest sensitivity and best maintenance conditions.Suspension Assembly Kits: Pre-assembled kits are available from the factory, or you can build your own kits using standard pipe fittings. Pipes and fittings are normally galvanized steel, but aluminum and stainless steel pipes and fittings are available. Units pictured above are secured to a steel cover plate that rests on a rectangular steel flange welded into the top of the vessel. Aluminum and stainless coverplates and flanges are also available. Standard 48" long x 1" pipe provides working depth (WD) up to 48". Longer pipe (to provide greater WD) is available. GS Series switches have upper (L1 = 28" standard) and lower (L2 = 20" standard) 1" pipes, with a tee (for stilling pot) in between. A stilling pot is required to equalize pressure and keep dirt from building up behind the diaphragm. PS series require a 1/2" conduit in 1" suspension pipe for explosion-proof applications. The 1/2" conduit (56" standard length) is a standard part of the GS series assembly.

The Series PLS2 is an electromechanical level switch designed for level monitoring of bulk materials. The rotating measuring vane is driven by a brushless synchronous motor at one revolution per minute. As product builds up, the paddle rotation is impeded and the resulting motor torque activates the output switch and stops the motor. A spring mechanism reactivates the motor and returns the switch to normal state when the material no longer impedes the paddle rotation. A torque adjusting mechanism eliminates the need for different sized paddles. The PLS2 is designed with the industry standard 1-1/4" male NPT connection and unit can be side or top mounted.